About
Encoders are special sensors that are added to each brushless motor of a Gimbal Stabilizer allowing the system to more accurately track motor position for increased stability which in turn also increases battery efficiency.
What's encoder technology in brushless gimbal control system?
The 3 axis stabilization gimbal system that relies on both active motor-driven components and passive inertial stabilization. Passive stabilization relies on the principles of inertia (the tendency of an object to resist change in its motion) and requires that the camera is well-balanced in the Pan, Tilt, and Roll Axes. Active stabilization refers to the techniques of using sensors to measure the camera’s Pan, Tilt, and Roll movements and counteract those movements using motors attached to the 3 axes.
Features
Easy to do gimbal tuning,no need to do much calibration work anymore.
Power saving, 5 times long working time than gimbal without encoder system.
Twin IMUs.
Faster response,motor torque increasing instantly,no bug for difficult rotating angle any more.
Encoder chip A5048a
Specifications
Model: GM110-8
Motor Out Diameter: Ф110±0.05mm
Configuration: 24N/28P
Motor Height: 33.9±0.2mm (Included with Encoder housing)
Hollow Shaft(OD): N/A
Hollow Shaft(ID): N/A
Wire Length: 610±3mm
Cable AWG: #24
Motor Weight: 610±3g
Wire plug: 2.5mm dupont connector
No-load current: 0.09±0.1 A
No-load volts: 20V
No-load Rpm: 125~139 RPM
Load current: 2A
Load volts: 20V
Load torque(g): 8000-12000
Motor internal resistance: 20.19Ω±5%（Resistance varies with temperature）
High voltage test: DC500V 1mA @2sec
Rotor housing runout: ≤0.1mm
Steering (axle extension): clockwise
High-low temperature test:
High temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature
Low temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature
Maximum power: ≤60W
Working current: 4-6S
Working temperature: -20~60℃;10~90%RH
Packing List
3 x GM110-8 Gimbal Motor with AS5048A Encoder & Magnet
1 x Alexmos 32BIT BGC Board Encoder version without alum case
1 x Connecting cables set
Encoders are special sensors that are added to each brushless motor of a Gimbal Stabilizer allowing the system to more accurately track motor position for increased stability which in turn also increases battery efficiency.
What's encoder technology in brushless gimbal control system?
The 3 axis stabilization gimbal system that relies on both active motor-driven components and passive inertial stabilization. Passive stabilization relies on the principles of inertia (the tendency of an object to resist change in its motion) and requires that the camera is well-balanced in the Pan, Tilt, and Roll Axes. Active stabilization refers to the techniques of using sensors to measure the camera’s Pan, Tilt, and Roll movements and counteract those movements using motors attached to the 3 axes.
Features
Easy to do gimbal tuning,no need to do much calibration work anymore.
Power saving, 5 times long working time than gimbal without encoder system.
Twin IMUs.
Faster response,motor torque increasing instantly,no bug for difficult rotating angle any more.
Encoder chip A5048a
Specifications
Model: GM110-8
Motor Out Diameter: Ф110±0.05mm
Configuration: 24N/28P
Motor Height: 33.9±0.2mm (Included with Encoder housing)
Hollow Shaft(OD): N/A
Hollow Shaft(ID): N/A
Wire Length: 610±3mm
Cable AWG: #24
Motor Weight: 610±3g
Wire plug: 2.5mm dupont connector
No-load current: 0.09±0.1 A
No-load volts: 20V
No-load Rpm: 125~139 RPM
Load current: 2A
Load volts: 20V
Load torque(g): 8000-12000
Motor internal resistance: 20.19Ω±5%（Resistance varies with temperature）
High voltage test: DC500V 1mA @2sec
Rotor housing runout: ≤0.1mm
Steering (axle extension): clockwise
High-low temperature test:
High temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature
Low temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature
Maximum power: ≤60W
Working current: 4-6S
Working temperature: -20~60℃;10~90%RH
Packing List
3 x GM110-8 Gimbal Motor with AS5048A Encoder & Magnet
1 x Alexmos 32BIT BGC Board Encoder version without alum case
1 x Connecting cables set
iPower GM110-8 Encoder Combo Set
- Regular price
- €959,90
- Sale price
- €959,90
- Regular price
-
On-Demand Product!
On-Demand Product!
Taxes and duties included?
Taxes and duties included?
Crashed hard?
Crashed hard?
Couldn't load pickup availability
