BLITZ Mini F7 Stack (E55 Mini 4in1 ESC) - iFlight Europe
    BLITZ Mini F7 Stack (E55 Mini 4in1 ESC) - iFlight Europe
BLITZ Mini F7 Stack (E55 Mini 4in1 ESC) - iFlight Europe
BLITZ Mini F7 Stack (E55 Mini 4in1 ESC) - iFlight Europe
    BLITZ Mini F7 Stack (E55 Mini 4in1 ESC) - iFlight Europe
BLITZ Mini F7 Stack (E55 Mini 4in1 ESC) - iFlight Europe

Über

Beschreibung

Our latest BLITZ Mini Stack used in our iFlight BNFs. Ultra fast F7 MCU, powerful 55A for 2-6S batteries. 20x20 mounting pattern. The perfect match for your new frame.

Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging.

 

FC Specifications:

MCU: STM32 F722

Gyro: ICM42688

Barometer: DPS310

OSD Chip: AT7456

Flash: 8MB (Blackbox flash)

UARTS: 6

Motor outputs: 4x (SH1.0 connector)

I2C serial: SDA/SLA pads

Smartaudio / IRC Tramp VTX protocol supported

LED controller: Yes

Beeper pad: Yes

Firmware target: IFRC-IFLIGHT_BLITZ_F722

Mount pattern: 20x20 mm / 4mm PCB hole diameter, silicon grommets for M3 screws

Dimensions: 30.5x27 mm

Weight: 5g

 

Wiring Suggestions:

UART 1 for VTX HD / Analog

UART 2 for a Receiver

UART 3/4/5 for GPS or other sensors that require a serial port

UART 6 for ESC Telemetry

 

ESC Specifications:

Mounting Holes: 20*20mm/Φ4mm

Weight: 11.3g

Supports 2-6S Lipo input

MCU: G071

Constant: 55 Amps 

Burst: 65 Amps

Current sensor: Yes

BEC: No

Current rate: 200

Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.

Firmware: BLHeli 32

Target: IFLIGHT_BLITZ_G071_01 32.9

Firmware: BLHeli 32

 

Wiring Diagram:

https://drive.google.com/drive/u/1/folders/17Uf67I6ER_z-otviR0I7tSqO31W7S553

 

Packing List:

1 x BLITZ Mini F7 V1.2 Flight Controller

1 x BLITZ Mini E55 4-IN-1 2-6S ESC

1 x silicon grommets

1 x wire harness for F7 Flight controller

 

Note:

If you need to use the ESC in the iH3 O3 Frame kit, please remove the capacitor after receiving the ESC, and then install the ESC.

Beschreibung

Our latest BLITZ Mini Stack used in our iFlight BNFs. Ultra fast F7 MCU, powerful 55A for 2-6S batteries. 20x20 mounting pattern. The perfect match for your new frame.

Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging.

 

FC Specifications:

MCU: STM32 F722

Gyro: ICM42688

Barometer: DPS310

OSD Chip: AT7456

Flash: 8MB (Blackbox flash)

UARTS: 6

Motor outputs: 4x (SH1.0 connector)

I2C serial: SDA/SLA pads

Smartaudio / IRC Tramp VTX protocol supported

LED controller: Yes

Beeper pad: Yes

Firmware target: IFRC-IFLIGHT_BLITZ_F722

Mount pattern: 20x20 mm / 4mm PCB hole diameter, silicon grommets for M3 screws

Dimensions: 30.5x27 mm

Weight: 5g

 

Wiring Suggestions:

UART 1 for VTX HD / Analog

UART 2 for a Receiver

UART 3/4/5 for GPS or other sensors that require a serial port

UART 6 for ESC Telemetry

 

ESC Specifications:

Mounting Holes: 20*20mm/Φ4mm

Weight: 11.3g

Supports 2-6S Lipo input

MCU: G071

Constant: 55 Amps 

Burst: 65 Amps

Current sensor: Yes

BEC: No

Current rate: 200

Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.

Firmware: BLHeli 32

Target: IFLIGHT_BLITZ_G071_01 32.9

Firmware: BLHeli 32

 

Wiring Diagram:

https://drive.google.com/drive/u/1/folders/17Uf67I6ER_z-otviR0I7tSqO31W7S553

 

Packing List:

1 x BLITZ Mini F7 V1.2 Flight Controller

1 x BLITZ Mini E55 4-IN-1 2-6S ESC

1 x silicon grommets

1 x wire harness for F7 Flight controller

 

Note:

If you need to use the ESC in the iH3 O3 Frame kit, please remove the capacitor after receiving the ESC, and then install the ESC.

Verdienen Sie Cashback bei jedem Einkauf
Erhalten Sie Treuepunkte für alle Einkäufe.
Electronics von iFlight-RC Europe

BLITZ Mini F7 Stack (E55 Mini 4in1 ESC)

Normaler Preis
€144,90
Verkaufspreis
€144,90
Normaler Preis
€167,90
Steuern inklusive.
Our latest BLITZ Mini Stack used in our iFlight BNFs. Ultra fast F7 MCU, powerful 55A for 2-6S batteries. 20x20 mounti...  Weiterlesen
Our latest BLITZ Mini Stack used in our iFlight BNFs. Ultra fast F7 MCU, powerful 55A for 2-6S batteries. 20x20 mounting pattern. The perfect match for your new frame. Improved circuit design, better components and lower electrical noise! DJI HD VTX Connector (Plug-and-Play / No soldering required), FC indicator LEDs for visual debugging.
35 jetzt auf Lager
Offizieller iFlight-RC Europe Store
Produkte werden aus Österreich versendet
Keine Zusatzgebühren für EU-Mitgliedstaaten
Exkl. GB, CH, NO, LI, etc.
Blitzschneller Versand
Express, Standard oder Gratis
Europa Shop Benefits
6 Monate kostenlose Reparaturen (exkl. Teile)

B2B Accounts verfügbar

Business Application Form

Schauen Sie sich diese verwandten Produkte an