About
Encoders are special sensors that are added to each brushless motor of a Gimbal Stabilizer allowing the system to more accurately track motor position for increased stability which in turn also increases battery efficiency.
What's encoder technology in brushless gimbal control system?
The 3 axis stabilization gimbal system that relies on both active motor-driven components and passive inertial stabilization. Passive stabilization relies on the principles of inertia (tendency of an object to resist change in its motion) and requires that the camera is well-balanced in the Pan, Tilt, and Roll Axes. Active stabilization refers to the techniques of using sensors to measure the camera’s Pan, Tilt, and Roll movements and counteract those movements using motors attached to the 3 axes.
Features
Easy to do gimbal tuning, no need to do much calibration work any more.
Power saving, 5 times long working time than gimbal without encoder system.
Twin IMUs.
Faster response, motor torque increasing instantly, no bug for difficult rotating angle any more.
Encoder chip AS5048A
Specifications
Model: GM5208
Motor Out Diameter: Ф63±0.05mm
Configuration: 12N/14P
Motor Height: 30.7±0.2mm (Included with Encoder housing)
Hollow Shaft(OD): Ф15-0.008/-0.012 mm
Hollow Shaft(ID): Ф12+0.05/0 mm
Wire Length: 610±3mm
Cable AWG: #24
Motor Weight: 209±0.5g
Wire plug: 2.5mm dupont connector
No-load current: 0.09±0.1 A
No-load volts: 20V
No-load Rpm: 456~504 RPM
Load current: 1A
Load volts: 20V
Load torque(g): 1800-2500
Motor internal resistance: 15.2Ω±5%(Resistance varies with temperature)
High voltage test: DC500V 10mA @1sec
Rotor housing runout: ≤0.1mm
Steering (axle extension): clockwise
High-low temperature test:
High temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature
Low temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature
Maximum power: ≤40W
Working Voltage: 3-5S
Working temperature: -20~60℃;10~90%RH
Packing List
3 x GM5208-12 Gimbal Motor with AS5048A Encoder & Magnet
1 x Alexmos 32BIT BGC Board Encoder version without alum case
1 x Connecting cables set
Encoders are special sensors that are added to each brushless motor of a Gimbal Stabilizer allowing the system to more accurately track motor position for increased stability which in turn also increases battery efficiency.
What's encoder technology in brushless gimbal control system?
The 3 axis stabilization gimbal system that relies on both active motor-driven components and passive inertial stabilization. Passive stabilization relies on the principles of inertia (tendency of an object to resist change in its motion) and requires that the camera is well-balanced in the Pan, Tilt, and Roll Axes. Active stabilization refers to the techniques of using sensors to measure the camera’s Pan, Tilt, and Roll movements and counteract those movements using motors attached to the 3 axes.
Features
Easy to do gimbal tuning, no need to do much calibration work any more.
Power saving, 5 times long working time than gimbal without encoder system.
Twin IMUs.
Faster response, motor torque increasing instantly, no bug for difficult rotating angle any more.
Encoder chip AS5048A
Specifications
Model: GM5208
Motor Out Diameter: Ф63±0.05mm
Configuration: 12N/14P
Motor Height: 30.7±0.2mm (Included with Encoder housing)
Hollow Shaft(OD): Ф15-0.008/-0.012 mm
Hollow Shaft(ID): Ф12+0.05/0 mm
Wire Length: 610±3mm
Cable AWG: #24
Motor Weight: 209±0.5g
Wire plug: 2.5mm dupont connector
No-load current: 0.09±0.1 A
No-load volts: 20V
No-load Rpm: 456~504 RPM
Load current: 1A
Load volts: 20V
Load torque(g): 1800-2500
Motor internal resistance: 15.2Ω±5%(Resistance varies with temperature)
High voltage test: DC500V 10mA @1sec
Rotor housing runout: ≤0.1mm
Steering (axle extension): clockwise
High-low temperature test:
High temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature
Low temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature
Maximum power: ≤40W
Working Voltage: 3-5S
Working temperature: -20~60℃;10~90%RH
Packing List
3 x GM5208-12 Gimbal Motor with AS5048A Encoder & Magnet
1 x Alexmos 32BIT BGC Board Encoder version without alum case
1 x Connecting cables set
iPower GM5208-12 Encoder Combo Set
- Regular price
- £351.00
- Sale price
- £351.00
- Regular price
-