{"title":"Gimbal Motors","description":"","products":[{"product_id":"ipower-gm8112-80t-gimbal-motor","title":"iPower GM8112-80T Gimbal Motor","description":"\u003cp\u003eThe GM8112 motor by iPower Motors is the ultimate brushless gimbal motor for Red Epic \/ Large Cameras. This motor\u003c\/p\u003e\n\u003cp\u003eis designed for large scale multi-rotor platforms looking to lift Red Epic \u0026amp; DSLR sized gear – 6KG\/cm Torque. The\u003c\/p\u003e\n\u003cp\u003eprinciple of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very\u003c\/p\u003e\n\u003cp\u003esimilar to regular gimbal based on hobby servo.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n\u003cp\u003eModel: GM8112\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф89.5±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 36N\/42P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 26±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф25-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф22+0.05\/+0.1 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 428±1g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.3±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 22V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 380~420 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 2A \u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 6000-9000\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 4.2Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤80W\u003c\/p\u003e\n\u003cp\u003eWorking current: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003e1 x GM8112 Gimbal Motor\u003c\/span\u003e\u003c\/p\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":45207786291465,"sku":"G006436","price":155.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm8112-80t-gimbal-motor-465954.png?v=1711099353"},{"product_id":"ipower-gm3506-gimbal-motor","title":"iPower GM3506 Gimbal Motor","description":"\u003cp\u003e\u003cspan\u003eThe GM35 series motor by iPower Motors is the ultimate brushless gimbal motor for SLR and similar weight Cameras. This motor is designed for large-scale multi-rotor platforms looking to lift SLR sized gear – 1.5KG\/cm Torque. The principle of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eCompatible Sliprings\u003c\/h3\u003e\n\u003cp\u003eCurrently none available\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eSpecifications:\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003eModel: GM3506\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф40±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/22P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 17.8±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф12-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф8.6+0.05\/0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 64±0.2g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.17±0.05 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 16V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 2149~2375 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 12V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 600-1000\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 5.6Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test: \u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 2-3S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List:\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003e1 x GM3506 gimbal motor\u003c\/span\u003e\u003c\/p\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":55399747813641,"sku":"G006282","price":28.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm3506-gimbal-motor-174896.png?v=1711099353"},{"product_id":"ipower-gm2804-gimbal-motor","title":"iPower GM2804 Gimbal Motor","description":"\u003cp\u003eThe controller can be used for building high-quality 3-axis camera stabilizing systems which can be mounted to UAV and for building handheld camera stabilizers.\u003c\/p\u003e\n\u003cp\u003eThis version of the controller is our new direction in the development of the stabilizing solutions. It will replace the previous 8-bit version of the SimpleBGC controller, keeping 100% back-compatibility, but adding the new functionality.\u003c\/p\u003e\n\u003ch3\u003eCompatible Sliprings\u003c\/h3\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iflight-rc.eu\/products\/ipower-gimbal-motor-slipring-od-6-5mm\"\u003eiPower Gimbal Motor Slipring - OD 6.5mm\u003c\/a\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n\u003cp\u003eModel: GM2804\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф35±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 12N\/14P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 15±0.2mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф8-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф6.5+0.05\/0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 60±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 42.3±0.2g\u003c\/p\u003e\n\u003cp\u003eWire plug: PH3P connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.09±0.05 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 10V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 1602~1771 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 0.8A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 10V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 250-350\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 9Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 2-3S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List:\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003e1 x iPower GM2804H-100T Gimbal Motor\u003c\/span\u003e\u003c\/p\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":55399743291657,"sku":"G006983","price":26.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm2804-gimbal-motor-814306.png?v=1711182135"},{"product_id":"ipower-gm2804-gimbal-motor-with-encoder","title":"iPower GM2804 Gimbal Motor with Encoder","description":"\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003eThe GM2804 motor by iPower Motors is the ultimate brushless gimbal motor for GoPro Cameras. This motor is designed for small multi-rotor platforms looking to lift GoPro sized gear – 0.5-1KG\/cm Torque.\u003c\/p\u003e\n\u003cp\u003eThe principle of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003eModel: GM2804\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф35±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 12N\/14P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 25±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф8-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф6.5+0.05\/0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 60±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 51±0.2g\u003c\/p\u003e\n\u003cp\u003eWire plug: PH3P connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.09±0.05 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 10 V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 1602~1771 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 0.8 A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 10 V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 250-350\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 9Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test: \u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 2-3S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003ePacking List\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003e1 x iPower GM2804 Gimbal Motor with Encoder\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":55399686308105,"sku":"GD17444","price":46.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm2804-gimbal-motor-wencoder-152573.png?v=1711182135"},{"product_id":"ipower-gm8112-80t-gimbal-motor-with-encoder","title":"iPower GM8112-80T Gimbal Motor with Encoder","description":"\u003cp\u003e\u003cspan\u003eThe GM8112 motor by iPower Motors is the ultimate brushless gimbal motor for Red Epic \/ Large Cameras. This motor is designed for large scale multi-rotor platforms looking to lift Red Epic \u0026amp; DSLR sized gear – 6KG\/cm Torque. The principle of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eSpecifications:\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003eModel: GM8112\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф89.5±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 36N\/42P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 33.4±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф25-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф22+0.05\/+0.1 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 446±1g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.3±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 22V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 380~420 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 2A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 6000-9000\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 4.2Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤80W\u003c\/p\u003e\n\u003cp\u003eWorking current: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List:\u003c\/h3\u003e\n\u003cp data-sider-select-id=\"0d6b6628-0a7f-45f7-a19e-081cc765d7ec\"\u003e1 x iPower GM8112 Gimbal Motor\u003c\/p\u003e\n\u003cp data-sider-select-id=\"0d6b6628-0a7f-45f7-a19e-081cc765d7ec\"\u003e1 x  AS5048A Encoder with aluminum case\u003c\/p\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":45218372878601,"sku":"GD17436","price":182.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm8112-80t-gimbal-motor-w-encoder-216004.png?v=1711347896"},{"product_id":"ipower-gm3506-gimbal-motor-with-encoder","title":"iPower GM3506 Gimbal Motor with Encoder","description":"\u003ch3\u003e\u003cspan\u003eGM3506 Gimbal motor with Encoder AS5048A\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003eThe GM35 series motor by iPower Motors is the ultimate brushless gimbal motor for SLR and similar weight Cameras. This motor is designed for large-scale multi-rotor platforms looking to lift SLR sized gear – 1.5KG\/cm Torque. The principle of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/p\u003e\n\u003cp\u003eEncoders are special sensors that are added to each brushless motor of a Gimbal Stabilizer allowing the system to more accurately track motor position for increased stability which in turn also increases battery efficiency.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cp\u003eEasy to do gimbal tuning, no need to do much calibration work any more.\u003c\/p\u003e\n\u003cp\u003ePower saving, 5 times long working time than gimbal without encoder system.\u003c\/p\u003e\n\u003cp\u003eTwin IMUs.\u003c\/p\u003e\n\u003cp\u003eFaster response, motor torque increasing instantly, no bug for difficult rotating angle any more.\u003c\/p\u003e\n\u003cp\u003eEncoder chip AS5048A\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eCompatible Sliprings\u003c\/h3\u003e\n\u003cp\u003eCurrently none available\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003eModel: GM3506\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф40±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/22P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 25.8±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф12-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф8.6+0.05\/0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 72±0.2g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.17±0.05 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 16V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 2149~2375 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 12V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 600-1000\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 5.6Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test: \u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 2-3S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cp data-sider-select-id=\"eef1707d-8f0a-4a66-a93d-ebbfa448be04\"\u003e1 x iPower GM3506 Gimbal Motor\u003c\/p\u003e\n\u003cp data-sider-select-id=\"eef1707d-8f0a-4a66-a93d-ebbfa448be04\"\u003e1 x  AS5048A Encoder with aluminum case\u003c\/p\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":55399752761609,"sku":"GD17443","price":50.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm3506-gimbal-motor-wencoder-931275.png?v=1720755088"},{"product_id":"ipower-gm110-10-gimbal-motor","title":"iPower GM110-10 Gimbal Motor","description":"\u003cp\u003e\u003cspan\u003eThe principle of the camera stabilization using brushless direct-drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eSpecial designed for SLR aerial and Z axis DIY Parts\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eFeatures\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003eSealed Case to prevent contamination by dust and dirt.\u003c\/p\u003e\n\u003cp\u003eHollow shaft for slipring\u003c\/p\u003e\n\u003cp\u003eConfiguration: 36N42P ,prove more torque.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003eModel: GM110-10\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф110±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 36N\/42P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 26±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф25-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф22+0.05\/+0.1 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 532±1g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.16±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20 V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 292~323 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 2 A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20 V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 9000-15000\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 4.16Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤80W\u003c\/p\u003e\n\u003cp\u003eWorking current: 4-6S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003e1 x GM110-10 brushless gimbal motor\u003c\/span\u003e\u003c\/p\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":48242302681353,"sku":"G006437","price":227.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm110-10-gimbal-motor-849958.png?v=1722909500"},{"product_id":"ipower-gm110-10-gimbal-motor-with-encoder","title":"iPower GM110-10 Gimbal Motor with Encoder","description":"\u003cp\u003e\u003cspan\u003eThe AS5048 is an easy-to-use 360° angle position sensor with a 14-bit high-resolution output. The maximum system accuracy is 0.05° assuming linearization and averaging is done by the external microcontroller. The IC measures the absolute position of the magnet’s rotation angle and consists of Hall sensors, the analog-digital converter, and digital signal processing. The zero position can be programmed via SPI or IC command. Therefore no programmer is needed anymore. This simplifies the assembly of the complete system because the zero position of the magnet does not need to be mechanically aligned. This helps developers to shorten their developing time. The sensor tolerates misalignment, air gap variations, temperature variations and as well as external magnetic fields. This robustness and wide temperature range (-40°C up to +150°C) of the AS5048 makes the IC ideal for rotation angle sensing in harsh industrial and medical environments. Several AS5048 ICs can be connected in the daisy chain for serial data read out. The absolute position information of the magnet is directly accessible over a PWM output and can be read out over a standard SPI or a high-speed IC interface. Version AS5048A comes with SPI and PWM Interface. Version AS5048B is configured with the IC interface and has also a PWM output. An internal voltage regulator allows the AS5048 to operate at either 3.3 V or 5 V supplies.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eIt is specially designed for iPower Motor GBM5208 GBM6208 GBM6212 GBM8017 GBM8028 GBM8108 GBM110 Motor, Please note that there should be screw holes on the gimbal motor to fit the metal mounting plate, otherwise you'll need to DIY to mount. The dimension of the aluminum alloy part is shown below.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eFeatures\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003e360° contactless angle position sensor  \u003c\/p\u003e\n\u003cp\u003eStandard SPI or high speed IC interface and PWM \u003c\/p\u003e\n\u003cp\u003eSimple programmable zero position via SPI or IC command  \u003c\/p\u003e\n\u003cp\u003eNo programmer needed\u003c\/p\u003e\n\u003cp\u003e14-bit full scale resolution 0.0219°\/LSB  \u003c\/p\u003e\n\u003cp\u003eAngle accuracy 0.05°after system linearization and averaging \u003c\/p\u003e\n\u003cp\u003eDaisy chain capability  \u003c\/p\u003e\n\u003cp\u003eTolerant to air gap variations   magnetic field input range: 30mT – 70mT \u003c\/p\u003e\n\u003cp\u003e-40°C to +150°C ambient temperature range \u003c\/p\u003e\n\u003cp\u003e3.3V \/ 5V compliant \u003c\/p\u003e\n\u003cp\u003e14-pin TSSOP package (5x6.4mm)\u003c\/p\u003e\n\u003cp\u003eMagnets size 6mm x 2.5mm\u003c\/p\u003e\n\u003cp\u003eThe principle of the camera stabilization using brushless direct-drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/p\u003e\n\u003cp\u003eSpecially designed for SLR aerial and Z-axis DIY Parts\u003c\/p\u003e\n\u003cp\u003eSealed Case to prevent contamination by dust and dirt.\u003c\/p\u003e\n\u003cp\u003eHollow shaft for slipring\u003c\/p\u003e\n\u003cp\u003eConfiguration: 36N42P ,prove more torque.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003eModel: GM110-10\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф110±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 36N\/42P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 33.4±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф25-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф22+0.05\/+0.1 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 556±1g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.16±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20 V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 292~323 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 2 A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20 V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 9000-15000\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 4.16Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤80W\u003c\/p\u003e\n\u003cp\u003eWorking current: 4-6S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cp\u003e1 x GM110-10 brushless gimbal motor\u003c\/p\u003e\n\u003cp\u003e1 x  AS5048A Encoder with aluminum case\u003c\/p\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":48242309005577,"sku":"GD17437","price":254.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm110-10-gimbal-motor-wencoder-728710.png?v=1722909502"},{"product_id":"ipower-gm110-8-gimbal-motor","title":"iPower GM110-8 Gimbal Motor","description":"\u003cp\u003e\u003cspan\u003eThe principle of the camera stabilization using brushless direct-drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cp\u003eSealed Case to prevent contamination by dust and dirt.\u003c\/p\u003e\n\u003cp\u003eHollow shaft for slipring\u003c\/p\u003e\n\u003cp\u003eConfiguration:24N28P,prove more torque.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003eModel: GM110-8\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф110±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/28P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 26±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): N\/A\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): N\/A\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 534±1g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.09±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20 V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 125~139 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 2A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 8000-12000\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 20.19Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤60W\u003c\/p\u003e\n\u003cp\u003eWorking current: 4-6S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003e1 x GM110-8 brushless gimbal motor\u003c\/span\u003e\u003c\/p\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":48242325946633,"sku":"CD06475","price":203.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm110-8-gimbal-motor-289002.png?v=1722909504"},{"product_id":"ipower-gm110-8-gimbal-motor-with-encoder","title":"iPower GM110-8 Gimbal Motor with Encoder","description":"\u003cp\u003e\u003cspan\u003eThe principle of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eFeatures\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003eSealed Case to prevent contamination by dust and dirt.\u003c\/p\u003e\n\u003cp\u003eHollow shaft for slipring\u003c\/p\u003e\n\u003cp\u003eConfiguration:24N28P,provide more torque.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003eModel: GM110-8\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф110±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/28P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 33.9±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): N\/A\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): N\/A\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 610±3g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.09±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 125~139 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 2A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 8000-12000\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 20.19Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤60W\u003c\/p\u003e\n\u003cp\u003eWorking current: 4-6S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cp data-sider-select-id=\"c501646f-57d6-4e82-b811-c39f3a452d43\"\u003e1 x iPower GM110-8 Gimbal Motor\u003c\/p\u003e\n\u003cp data-sider-select-id=\"c501646f-57d6-4e82-b811-c39f3a452d43\"\u003e1 x  AS5048A Encoder with aluminum case\u003c\/p\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":48242332533001,"sku":"GD17438","price":230.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm110-8-gimbal-motor-w-encoder-846280.png?v=1722909504"},{"product_id":"ipower-gm5208-12-gimbal-motor","title":"iPower GM5208-12 Gimbal Motor","description":"\u003cp\u003e\u003cspan\u003eThe GM52 series motor by iPower Motors is the ultimate brushless gimbal motor for DSLR \/ CANON 5D MARKII, MARKIII Cameras.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThis motor is designed for large-scale multi-rotor platforms looking to lift Red Epic \u0026amp; DSLR sized gear – 4KG\/cm Torque.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThe principle of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eSpecifications\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003eModel: GM5208\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф63±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 12N\/14P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 22.7±0.2mm \u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф15-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф12+0.05\/0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 195±0.5g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.09±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 456~504 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 1800-2500\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 15.2Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 10mA @1sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤40W\u003c\/p\u003e\n\u003cp\u003eWorking Voltage: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003e1 x GM5208-12 gimbal motor\u003c\/span\u003e\u003c\/p\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":48379688091913,"sku":"G007636","price":47.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm5208-12-gimbal-motor-830685.png?v=1725633819"},{"product_id":"ipower-gm5208-12-gimbal-motor-with-encoder","title":"iPower GM5208-12 Gimbal Motor with Encoder","description":"\u003cp\u003eThe GM52 series motor by iPower Motors is the ultimate brushless gimbal motor for DSLR \/ CANON 5D MARKII, MARKIII Cameras.\u003c\/p\u003e\n\u003cp\u003eThis motor is designed for large-scale multi-rotor platforms looking to lift Red Epic \u0026amp; DSLR sized gear – 4KG\/cm Torque.\u003c\/p\u003e\n\u003cp\u003eThe principle of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003eModel: GM5208-12\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф63±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 12N\/14P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 30.7±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф15-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф12+0.05\/0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 209±0.5g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.09±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 456~504 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 1800-2500\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 15.2Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 10mA @1sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤40W\u003c\/p\u003e\n\u003cp\u003eWorking Voltage: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cp data-sider-select-id=\"2974490a-59cc-44aa-8407-55c48d89db31\"\u003e1 x iPower GM5208-12 Gimbal Motor\u003c\/p\u003e\n\u003cp data-sider-select-id=\"2974490a-59cc-44aa-8407-55c48d89db31\"\u003e1 x  AS5048A Encoder with aluminum case\u003c\/p\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":48379708473609,"sku":"GD17441","price":74.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm5208-12-gimbal-motor-wencoder-508643.png?v=1725633984"},{"product_id":"ipower-gm5208-24-gimbal-motor","title":"iPower GM5208-24 Gimbal Motor","description":"\u003cp\u003eThe GM52 series motor by iPower Motors is the ultimate brushless gimbal motor for DSLR \/ CANON 5D MARKII, MARKIII Cameras.\u003c\/p\u003e\n\u003cp\u003eThis motor is designed for large-scale multi-rotor platforms looking to lift Red Epic \u0026amp; DSLR sized gear – 4KG\/cm Torque.\u003c\/p\u003e\n\u003cp\u003eThe principle of the camera stabilization using brushless direct drive motors, In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003eModel: GM5208-24\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф59.5±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/22P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 31.2±0.2mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф15-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф12.6+0.05\/0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 204±0.5g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.09±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 396~436 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 1800-2500\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 13.7Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 10mA @1sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤40W\u003c\/p\u003e\n\u003cp\u003eWorking Voltage: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cp\u003e1 x GM5208-24 gimbal motor\u003c\/p\u003e\n\u003cp\u003e1 x Screw bag\u003c\/p\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":48379736981769,"sku":"G006984","price":51.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-gm5208-24-gimbal-motor-890411.png?v=1725634163"},{"product_id":"ipower-gm4108h-120t-gimbal-motor","title":"iPower GM4108H-120T Gimbal Motor","description":"\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003eModel: GM4108H\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф47±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/22P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 32.3±0.2mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф10-0.008\/-0.012mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): 8+0.05\/0mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 265±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 124±0.5g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.07±0.1A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 513~567 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1.5A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 1200-1800\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 11.1Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA@2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): Clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test：\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature：Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003e\u003c\/h3\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003ePacking List\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003e1 x iPower GM4108H-120T Gimbal Motor\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":49185027981577,"sku":"GD07237","price":43.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/gm4108h-120t-gimbal-motor-593290.png?v=1739560868"},{"product_id":"ipower-gm4108h-120t-gimbal-motor-with-encoder","title":"iPower GM4108H-120T Gimbal Motor with Encoder","description":"\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003eModel: GM4108H\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф47±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/22P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 32.3±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф10-0.008\/-0.012mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): 8+0.05\/0mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 265±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 137±0.5g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.07±0.1A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 513~567 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1.5A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 1200-1800\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 11.1Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA@2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): Clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test：\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003ePacking List\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp data-sider-select-id=\"31d0d84b-7845-4f35-922d-263de492070d\"\u003e1 x iPower GM4108H-120T Gimbal Motor\u003c\/p\u003e\n\u003cp data-sider-select-id=\"31d0d84b-7845-4f35-922d-263de492070d\"\u003e1 x  AS5048A Encoder with aluminum case\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":49185058652425,"sku":"GD17442","price":66.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/gm4108h-120t-gimbal-motor-w-encoder-163761.png?v=1739560867"},{"product_id":"ipower-gm6208-150t-gimbal-motor","title":"iPower GM6208-150T Gimbal Motor","description":"\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003ch3\u003eHigh-Torque Brushless Gimbal Motor for DSLR \u0026amp; Cinema Cameras\u003c\/h3\u003e\n\u003cp\u003eThe iPower GM62 Series Motor is a professional-grade brushless gimbal motor engineered for high-performance camera stabilization.\u003cbr\u003eDesigned for large-scale gimbal systems, it easily handles DSLR and cinema cameras such as the Canon 5D Mark II\/III and RED Epic, delivering up to 4 kg·cm of torque for smooth and precise motion.\u003c\/p\u003e\n\u003cp\u003eBuilt on brushless direct-drive technology, the GM62 ensures silent operation, accurate control, and superior stability — outperforming traditional servo-based gimbals.\u003cbr\u003eIts robust design makes it ideal for heavy-lift multi-rotor platforms and professional cinematography applications.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cp\u003eHigh Torque Output: Up to 4 kg·cm for DSLR and cinema cameras.\u003c\/p\u003e\n\u003cp\u003eBrushless Direct-Drive Design: Smooth, quiet, and highly precise stabilization.\u003c\/p\u003e\n\u003cp\u003eCompatible Cameras: Canon 5D Mark II\/III, RED Epic, and similar models.\u003c\/p\u003e\n\u003cp\u003eHeavy-Lift Capability: Perfect for large multi-rotor or handheld gimbal setups.\u003c\/p\u003e\n\u003cp\u003eDurable Construction: Built for long-term reliability under demanding use.\u003c\/p\u003e\n\u003cp\u003eProfessional Performance: Ensures stable, vibration-free footage for filmmaking.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003eModel: GM6208\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф69.5±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/28P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 24±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф25-0.01\/-0.015 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф22+0.05\/+0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 249±0.5g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.08±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20 V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 209~231 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1.2 A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20 V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 2600-3600\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 32Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eCompatible Sliprings\u003c\/h3\u003e\n\u003cp\u003eNone Available at this time\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003ePacking List\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003e1 x GM6208-150T Gimbal Motor\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":55425076199689,"sku":"G006047","price":72.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/gm6208-150t-gimbal-motor-644387.png?v=1742544033"},{"product_id":"ipower-gm6208-150t-gimbal-motor-with-encoder","title":"iPower GM6208-150T Gimbal Motor with Encoder","description":"\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"title-product\"\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003ch3\u003eHigh-Torque Brushless Gimbal Motor for DSLR Cameras\u003c\/h3\u003e\n\u003cp\u003eThe iPower GM62 Series Motor is a powerful brushless gimbal motor engineered for professional camera stabilization.\u003cbr\u003eIt’s ideal for DSLR and cinema cameras such as the Canon 5D Mark II\/III or RED Epic, delivering up to 4 kg·cm of torque for perfectly smooth and stable movement.\u003c\/p\u003e\n\u003cp\u003eDesigned for heavy-lift multi-rotor platforms, this motor combines strength, precision, and reliability.\u003cbr\u003eUsing brushless direct-drive technology, it provides accurate, quiet, and responsive stabilization — outperforming traditional servo-based gimbals.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cp\u003eHigh Torque Output: Up to 4 kg·cm, ideal for DSLR and cinema cameras.\u003c\/p\u003e\n\u003cp\u003eCompatible Cameras: Canon 5D Mark II\/III, RED Epic, and similar setups.\u003c\/p\u003e\n\u003cp\u003eDirect-Drive Brushless Design: Smooth, silent, and highly precise stabilization.\u003c\/p\u003e\n\u003cp\u003eHeavy-Lift Capability: Perfect for large multi-rotor and professional aerial rigs.\u003c\/p\u003e\n\u003cp\u003eDurable Build: Designed for consistent performance under demanding conditions.\u003c\/p\u003e\n\u003cp\u003eProfessional Use: Optimized for cinematography, aerial filming, and gimbal builders.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp\u003eModel: GM6208\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф69.5±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 24N\/28P\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eMotor Height: 32±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф25-0.01\/-0.015 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф22+0.05\/+0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 610±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #24\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 265±0.5g\u003c\/p\u003e\n\u003cp\u003eWire plug: 2.5mm dupont connector\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.08±0.1 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 20 V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 209~231 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 1.2A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 20V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 2600-3600\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 32Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 3-5S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eCompatible Sliprings\u003c\/h3\u003e\n\u003cp\u003eNone Available at this time\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003ch3 class=\"temp-specs-td name\"\u003ePacking List\u003c\/h3\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cp data-sider-select-id=\"5d2b86c3-25ad-459b-83aa-b2ddfed5c74f\"\u003e1 x GM6208 150T Brushless Gimbal Motor\u003c\/p\u003e\n\u003cp data-sider-select-id=\"5d2b86c3-25ad-459b-83aa-b2ddfed5c74f\"\u003e1 x  AS5048A Encoder with aluminum case\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":55008345489673,"sku":"GD17439","price":98.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/GM6208-encoder.png?v=1742482492"},{"product_id":"gbm2804h-100t-gimbal-motor","title":"GBM2804H-100T Gimbal Motor","description":"\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cdiv\u003e\n\u003cdiv\u003e\n\u003cp\u003eThe GBM2804H-100T motor by iPower Motors are the ultimate brushless gimbal motor for GoPro Cameras.This motor is designed for small multi-rotor platforms looking to lift GoPro sized gear – 0.35KG\/cm Torque.The principle of the camera stabilization using brushless direct drive motors In fact, gimbal based on BLDC motors is very similar to regular gimbal based on hobby servo.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv\u003e\n\u003cp\u003eModel: GBM2804H-100T\u003c\/p\u003e\n\u003cp\u003eMotor Out Diameter: Ф35±0.05mm\u003c\/p\u003e\n\u003cp\u003eConfiguration: 12N\/14P\u003c\/p\u003e\n\u003cp\u003eMotor Height: 15±0.2mm (Included with Encoder housing)\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(OD): Ф7-0.008\/-0.012 mm\u003c\/p\u003e\n\u003cp\u003eHollow Shaft(ID): Ф5+0.05\/+0 mm\u003c\/p\u003e\n\u003cp\u003eWire Length: 300±3mm\u003c\/p\u003e\n\u003cp\u003eCable AWG: #28\u003c\/p\u003e\n\u003cp\u003eMotor Weight: 39±0.2g\u003c\/p\u003e\n\u003cp\u003eWire plug: N\/A\u003c\/p\u003e\n\u003cp\u003eNo-load current: 0.07±0.05 A\u003c\/p\u003e\n\u003cp\u003eNo-load volts: 10 V\u003c\/p\u003e\n\u003cp\u003eNo-load Rpm: 1468~1622 RPM\u003c\/p\u003e\n\u003cp\u003eLoad current: 0.8A\u003c\/p\u003e\n\u003cp\u003eLoad volts: 10 V\u003c\/p\u003e\n\u003cp\u003eLoad torque(g·cm): 250-350\u003c\/p\u003e\n\u003cp\u003eMotor internal resistance: 10Ω±5%（Resistance varies with temperature）\u003c\/p\u003e\n\u003cp\u003eHigh voltage test: DC500V 1mA @2sec\u003c\/p\u003e\n\u003cp\u003eRotor housing runout: ≤0.1mm\u003c\/p\u003e\n\u003cp\u003eSteering (axle extension): clockwise\u003c\/p\u003e\n\u003cp\u003eHigh-low temperature test:\u003c\/p\u003e\n\u003cp\u003eHigh temperature: Keep at 60℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eLow temperature: Keep at -20℃ for 100 hours, and the motor can work normally after 24 hours at room temperature\u003c\/p\u003e\n\u003cp\u003eMaximum power: ≤25W\u003c\/p\u003e\n\u003cp\u003eWorking current: 2-3S\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -20~60℃;10~90%RH\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cdiv\u003e\n\u003cp\u003e1 x GBM2804H-100T\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":56678013239561,"sku":"G006176","price":22.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/gbm2804h-100t-gimbal-motor-iflight-europe-6593139.png?v=1765474516"},{"product_id":"ex8108-105kv-multi-rotor-motor","title":"iPower eX8108 105KV Multi-Rotor Motor","description":"\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-tr\"\u003e\n\u003cdiv class=\"temp-specs-td value\"\u003e\n\u003cdiv\u003e\n\u003cdiv\u003e\n\u003cp\u003eKV: 105RPM\/V\u003c\/p\u003e\n\u003cp\u003eNO Load Current: 0.6A\/22.2V\u003c\/p\u003e\n\u003cp\u003eMax watts: 750W\/180S\u003c\/p\u003e\n\u003cp\u003eMax Amps: 24A\/180S\u003c\/p\u003e\n\u003cp\u003eResistance: 186MΩ\u003c\/p\u003e\n\u003cp\u003eMotor dimension: Φ87x24.50mm\u003c\/p\u003e\n\u003cp\u003eWeight: 228.6g\u003c\/p\u003e\n\u003cp\u003eRecommended Battery configuration: 6-12S\u003c\/p\u003e\n\u003cp\u003eRecommended CF Prop: 28inch, 29inch\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003ch3\u003ePacking List\u003c\/h3\u003e\n\u003cdiv\u003e\n\u003cp\u003e1 x eX8108 105KV Brushless Motor\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c!----\u003e","brand":"iFlight","offers":[{"title":"Default Title","offer_id":56678024053001,"sku":null,"price":119.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0657\/0527\/9753\/files\/ipower-ex8108-105kv-multi-rotor-motor-iflight-europe-2547621.png?v=1765474512"}],"url":"https:\/\/iflight-rc.eu\/en-br\/collections\/gimbal-motors.oembed","provider":"iFlight Europe","version":"1.0","type":"link"}